Ima nešto! Pokušat ću sutra ... paralelno i serijski karticu.
Otkrio sam novi Pionero V5:
Kraj, IC je otišao ...
Čemu služi taj Pionero?
Jel to maknut dropbox link sa uputama, kernelima... ?
Di su nestli filovi...ja taman zalemio ono, a sada nema filova?
Pokušavam Maggie Otpora JTAG.
Ima nešto, umjesto da samo ST20 ST40 i tipa matična trebate ga zamijeniti.
Izgleda da USB od starog maxtv-a nije nikada radio zato sto kada sam ga otvorio uopce nigdje nema FTDI IC nego ima samo mali IC od Texas Inst. koji sluzi za punjenje nekih uredaja.
Izgleda da USB od starog maxtv-a nije nikada radio zato sto kada sam ga otvorio uopce nigdje nema FTDI IC nego ima samo mali IC od Texas Inst. koji sluzi za punjenje nekih uredaja.
FTDI nema baš nikakve veze sa USB uređajima. On služi za USB-Serial konverziju, a USB kontroler je nešto drugo.
Svaki mikroprocesor koji prima i šalje podatke mora imati neki konverter sa SPI na USB standard.Samo u slučaju da procesor ima ugradeni kontroler onda mu netreba.
Svaki mikroprocesor koji prima i šalje podatke mora imati neki konverter sa SPI na USB standard.Samo u slučaju da procesor ima ugradeni kontroler onda mu netreba.
Da ponovim...
FTDI nema baš nikakve veze sa USB uređajima. On služi za USB-Serial konverziju, a USB kontroler je nešto drugo.
I nadodam:
SPI nema baš nikakve veze sa USB uređajima. On služi pretežno za komunikaciju s EEPROM memorijom ili IR receiverom. I da procesor nema ugrađen USB kontroler, opet nigdje nema USB-SPI sučelje za komunikaciju s USB uređajem, npr. stickom. USB je jedno, SPI je nešto drugo.
Da to su sam se zeznuo nije ISP nego UART.
Ucestali cip FT232 od FTDI-a sluzi za slanje i primanje podataka od MCU-a.Podatci se salju preko TX(Salje) i RX(Prima) pinova.Sto znaci da bi se MCU mogao programirati preko USB-a u slucaju da ima bootloader i ft232 cip.
Da to su sam se zeznuo nije ISP nego UART.
Ucestali cip FT232 od FTDI-a sluzi za slanje i primanje podataka od MCU-a.Podatci se salju preko TX(Salje) i RX(Prima) pinova.Sto znaci da bi se MCU mogao programirati preko USB-a u slucaju da ima bootloader i ft232 cip.
To opet nema veze s ugrađenim USB-ovima. Ugrađeni USB-ovi su host, a FT232 je client.
Ima neko filove za Albisa da mi da ih uploda i posalje link...tnx
Doniram u naučne svrhe:
T-Com Scientific Atlanta IPP330HD - bez napajanja i kablova
T-Com D-Link DSL-584T - bez napajanja i kablova
T-Com Thomson SpeedTouch 0783EA - bez napajanja neispravan (grom)
T-Com ISDN Eurit33 sa telefonom
T-Com Siemens ADSL A-100-1
Vip - Homebox GS III - komplet 2 komada
Bilo bi poželjno sve u paketu, jedino platiti dostavu iz Pule.
Slike u prilogu. PP otvoren
Oba dva Homeboxa su otišla jedan kolegi za Split, a drugi kolegi u Puli....
Pošto neće ići u sve paketu, onda kako tko želi
Doniram u naučne svrhe:
T-Com Scientific Atlanta IPP330HD - bez napajanja i kablova
T-Com D-Link DSL-584T - bez napajanja i kablova
T-Com Thomson SpeedTouch 0783EA - bez napajanja neispravan (grom)
T-Com ISDN Eurit33 sa telefonom
T-Com Siemens ADSL A-100-1
Vip - Homebox GS III - komplet 2 komada
Bilo bi poželjno sve u paketu, jedino platiti dostavu iz Pule.
Slike u prilogu. PP otvoren
Oba dva Homeboxa su otišla jedan kolegi za Split, a drugi kolegi u Puli....
Pošto neće ići u sve paketu, onda kako tko želi
Za Atlantu ima otključani bootloader i navodno neki OpenWRT, a inače je više-manje "zaboravljeni" uređaj.
Za DSL-584T postoji OpenWRT: http://wiki.openwrt.org/toh/d-link/dsl-584t
SpeedTouch se može rootati i koristiti kao SIP server ili klijent.
GS3 sam uspio debrandirati da se makne VIP splash na LCD-u i iz web sučelja (ima uputa na netu), a postoji i neslužbeni OpenWRT: http://forum.pcekspert.com/showthread.php?t=248444
Otključati se može za 7 eura sa DC-Unlockerom.
e nije 7 nego 15 
btw nabaviti openwrt img za GS3?
kolega gore mi je poklonio jednog, hvala TONYA_
isprike na OT
Hi!
There is another wiggler, the Pionero transcribed with flash. and albis. goes so far with ini:
I will not give up!
Still need to be refined the flash.ini and albis.ini ...
--------------------------------------
[ALBIS SC8000]
Flash1Start=60000000
Flash1Type=12
Flash2Start=60000000
Flash2Type=12
FirmwareAddress=7FE80000
ChannelListAddress=7FE10000
TrapAddress=C0010000
CombinedICs=False
-------------------------------------
[ST M28W160FS]
NumBlocks=35
ErasureMode=48
block0=000000
block1=010000
block2=020000
block3=030000
block4=040000
block5=050000
block6=060000
block7=070000
block8=080000
block9=090000
block10=0A0000
block11=0B0000
block12=0C0000
block13=0D0000
block14=0E0000
block15=0F0000
block16=100000
block17=110000
block18=120000
block19=130000
block20=140000
block21=150000
block22=160000
block23=170000
block24=180000
block25=190000
block26=1A0000
block27=1B0000
block28=1C0000
block29=1D0000
block30=1E0000
block31=1F0000
block32=1F8000
block33=1FA000
block34=1FC000
block35=200000
------------------------------------
These addresses and blocks can be good? I could not find a description of the M28W160FS ...
CPU Family is set to ST20. It should be ST40.
Tržim h1 STB polovni, znate li gdje bi se mogao nabaviti?
Nigdje. Tehničari ih ne ostavljaju korisnicima, neispravne uvijek pokupe.
Za što ti treba?
Kao drugi uređaj, taman mi fali još jedan.
nov sam u ovome. pa jel mi moze netko objasnit kako sve to namjestit i sto mi sve treba plzz:)
Hvala unaprijed
LP
Jel tema mrtva ili je to zatišje pred buru.
Moj Albis još čeka da ga pretvorim u player 
i moj čeka več godiu dana..
Hi!
Van másik!:
I finally got another Albis!
U-boot which is better?
Solder on the connectors and then go to the image.
There is another new image?
Da ima, pisalo bi.
Hi!
Uboot replaced, promt not pdk7105:
# /media/usb_sda1/flash_unlock /dev/mtd0 0x0 4
# cp /media/usb_sda1/u-boot.bin /tmp
# /media/usb_sda1/flashcp -v /tmp/u-boot.bin /dev/mtd0
Erasing blocks: 4/4 (100%)
Writing data: 196k/0k (100%)%)
Verifying data: 196k/0k (100%)%)
#
# reboot
# [ 433.864000] UBIFS: un-mount UBI device 7, volume 0
umount: can't remount none read-only
umount: none busy - remounted read-only
umount: can't remount none read-only
umount: can't remount none read-only
umount: none busy - remounted read-only
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
R[ 435.905000] Flash device refused suspend due to active operation (state 0)
[ 435.906000] Resü
Board: STB8xxx [32-bit mode]
U-Boot 1.3.1 (Mar 17 2011 - 10:33:23) - STB-8xxx-2.35se
DRAM: 256 MiB
NOR: 2 MiB
NAND: Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
128 MiB
In: serial
Out: serial
Err: serial
ENV: is valid
Load main kernel from NAND to RAM
Loading from NAND 128MiB 3,3V 8-bit, offset 0x1800000
Image Name: Main (dev) Kernel
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2759903 Bytes = 2.6 MiB
Load Address: 88000000
Entry Point: 88001000
Checking main image
## Checking Image at 82000000 ...
Image Name: Main (dev) Kernel
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2759903 Bytes = 2.6 MiB
Load Address: 88000000
Entry Point: 88001000
Verifying Checksum ... OK
found valid main image
Hit any key to stop autoboot: 0
STB8000>
Commands not works....
Retained in the new uboot, I can not go further.
Goto old u-boot:
NAND erase: device 0 offset 0x1900000, size 0x500000
Erasing at 0x1de0000 -- 100% complete.
OK
NAND write: device 0 offset 0x1900000, size 0x500000
5242880 bytes written: OK
PDK7105> run update_rootfs_usb
(Re)start USB...
USB: STM EHCI HCD initialization HCCR=0xfe1ffe00, HCOR=0xfe1ffe10, hc_length=16
Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading rootfs.img
67108864 bytes read
NAND erase: device 0 offset 0x2100000, size 0x5f00000
Skipping bad block at 0x07f80000
Skipping bad block at 0x07fa0000
Skipping bad block at 0x07fc0000
Skipping bad block at 0x07fe0000
OK
NAND write: device 0 offset 0x2100000, size 0x4000000
67108864 bytes written: OK
PDK7105>
After download new 2015 image, then restart or cold boot: Emergency delete flash error, delete all image in flash, only the u-boot was, fortunately...
After reset:
Hostname: SPARK7162.
Firmware has been updated, it looks good, but the 214k u-boot has been provided.
Currently, the net exchange remote.conf and fun ...
Yesterday's u-boot 194k as if it is older stb8000 promted me just given. I could not continue with the update, but it may be that I've done something wrong.
Thanks Raxone!
Could not ...
PDK7105 not the prompt, but that disturbed
STB8000 ...
Was changing the USB files.:
Board: STx7105-PDK [32-bit mode]
U-Boot 2010.09 (Sep 05 2014 - 21:05:55) - stm24-2014-R@x1
DRAM: 256 MiB
NOR: 2 MiB
NAND: 128 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: stmac-0
Hit any key to stop autoboot: 0
Loading from nand0, offset 0x1900000
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
** Unknown image type
Wrong Image Format for bootm command
ERROR: can't get kernel image!
PDK7105>
Hi!
After Flash only Hyperion v4 image, succes!:
___________ ___ _____________
\________ \ | | / _____ ____/
_____) | | |_/ / | | .---. ,--. _ .--..--.
| ___/ | __'. | | / /__\\ `'_\ : [ `.-. .-. |
| | | | \ \ | | | \__., // | |, | | | | | |
|_| |_| |_| |_| '.__.' \'-;__/ [___||__||__]
----------============ Polish Koders Team ============-----------
login[1245]: root login on 'ttyAS0'
BusyBox v1.21.1 (2014-02-23 22:58:31 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
spark7162:~# ___________ ___ _____________
Testing....
Lan not work... Therefore I can not switch to a remote control or other...
read configured interface: {'lo': {'dhcp': False}, 'eth0': {'dhcp': False, 'netmask': [0, 0, 0, 0], 'gateway': [0, 0, 0, 0], 'address': [0, 0, 0, 0]}}
self.ifaces after loading: {'eth0': {'preup': False, 'predown': False, 'ip': [0, 0, 0, 0], 'up': True, 'mac': 'dhcp': False, 'netmask': [0, 0, 0, 0], 'gateway': [0, 0, 0, 0]}}
Network after command ok, remote.conf replaced, testing:
ifconfig eth0 192.168.1.100 netmask 255.255.255.0
