Missing package:
checking for libcrystalhd/libcrystalhd_if.h... no
== Could not find libcrystalhd. CrystalHD support disabled. ==
checking for libcrystalhd soname... /home/ball/martiis-tdt/tdt/tufsbox/devkit/sh4/lib/gcc/sh4-linux/4.5.2/../../../../sh4-linux/bin/ld: mode shlelf_linux
to fixit install libcrystalhd-dev.
E: Package not found: libcrystalhd-dev
Ubuntu 11.04 not, only +12.04
http://packages.ubuntu.com/search?keywords=libcrystalhd-dev
Installed 12.04 libcrystalhd3, libcrystalhd-dev.deb, not work.
......................
I try to xbmc on scart, echo 576i50>/proc/stb/video/videomode:
ufs913:~# cat /proc/stb/video/videomode
proc_video_videomode_read
Found mode to set 576i50 at 23
proc_video_videomode_read
Found mode to set 576i50 at 23
proc_video_videomode_read
Found mode to set 576i50 at 23
576i50
ufs913:~#
------------------
I try it ubuntu 12.04, same error ( libcrystalhd-dev installed...):
pls. english.
@Raxone:
How to install in stb8000 uboot on pkt 5.1 or oldest image?
Now usb install kernel panic; how to not work (2015.12.17 pdk7105-PKT 5.1).
Board: STB8xxx [32-bit mode]
U-Boot 2010.09 (Feb 27 2016 - 20:03:42) - stm24-2016_Raxone
DRAM: 256 MiB
NOR: 2 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ENV: is valid
Net: stmac-0
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x0, size 0x300000
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
3145728 bytes read: OK
bootm - boot application image from memory
Usage:
bootm [addr [arg ...]]
- boot application image stored in memory
passing arguments 'arg ...'; when booting a Linux kernel,
'arg' can be the address of an initrd image
Sub-commands to do part of the bootm sequence. The sub-commands must be
issued in the order below (it's ok to not issue all sub-commands):
start [addr [arg ...]]
loados - load OS image
cmdline - OS specific command line processing/setup
bdt - OS specific bd_t processing
prep - OS specific prep before relocation or go
go - start OS
STB8000>
Hi!
PKT 5.1 green dead, needed reflash.
After reflash, albis not work:
E2 ERROR
INIT: Sending processes the TERM signal
lircd-0.9.0[741]: removeSending all processes the TERM signal...lircd-0.9.0[741]: caught signal
done.
Sending all processes the KILL signal...done.
Deactivating swap...umount: tmpfs busy - remounted read-only
done.
Unmounting local filesystems...umount: tmpfs busy - remounted read-only
done.
Rebooting... Restarting system.
Restart.. Restart...
How to run PKT 5.1 in stb8000 u-boot?
HDMU work, but kodidirect subsupport error next power on...
HDMU sound very overdriven and distorted.
There are two (three) Albis, but does not work...
You use old u-boot?!
Yes, pdk7105 u-boot, but new stb8000 u-boot not working pkt 5.1 the another Albis.
Ok, work, I was wrong howto used, old pkt5.1, these working:
,,If use old u-boot mtdparts is wrong you need change setenv"
Thanks, sorry.
Hi!
I'm trying to build the Audioniek git, but error:
https://github.com/Audioniek/StartHere
What do I do wrong?
Same error all git:
Do you want to start the build now (Y*/n)? Y
run... run.. run...
make: *** No rule to make target '/home/ball/StartHere-master/cdk/Patches/build-enigma2/linux-sh4-2.6.32.61_0217_ufs913.config.debug', needed by '.deps/linux-kernel'. Stop.
Ubuntu Mate 16.04 64 bit:
I ljudi dokle se došlo sa ovim projektom, ima li nade da ovaj stari 7710 proradi bez max-a
You must read log.
This file not exist /home/ball/StartHere-master/cdk/Patches/build-enigma2/linux-sh4-2.6.32.61_0217_ufs913.config.debug.
In configuration menu "Activate debug (y/N)? " you must say no.
It means whan kernel boot nothing display in terminal/rs232 only for u-boot and rootfs you see log but less than you got debug kernel configuration actived.
Ok, run. Build no debug, kernel 209. (Instead off: debug and 2011 kernel.)
Rename and copy file Patches/build-enigma2/linux-sh4-2.6.32.61_0217_ufs913.config to linux-sh4-2.6.32.61_0217_ufs913.config.debug.
Ended:
cp -p /home/ball/StartHere-master/tufsbox/cdkroot/usr/sbin/livestreamersrv /home/ball/StartHere-master/tufsbox/release/usr/sbin/ && \
cp -dp /home/ball/StartHere-master/tufsbox/cdkroot/sbin/mkfs /home/ball/StartHere-master/tufsbox/release/sbin/
cp: stat '/home/ball/StartHere-master/tufsbox/cdkroot/boot/uImage' sikertelen: Nincs ilyen fájl vagy könyvtár
Makefile:10307: recipe for target 'release_enigma2_base' failed
make: *** [release_enigma2_base] Error 1
root@ball:/home/ball/StartHere-master/cdk#
Start from again....
Fresh install, only albis patch, same error:
CC kernel/exec_domain.o
CC kernel/panic.o
CC kernel/printk.o
CC kernel/cpu.o
CC kernel/exit.o
CC kernel/itimer.o
TIMEC kernel/timeconst.h
Can't use 'defined(@array)' (Maybe you should just omit the defined()?) at kernel/timeconst.pl line 373.
/opt/StartHere/cdk/linux-sh4-2.6.32.46_stm24_0209/kernel/Makefile:129: recipe for target 'kernel/timeconst.h' failed
make[2]: *** [kernel/timeconst.h] Error 255
Makefile:903: recipe for target 'kernel' failed
make[1]: *** [kernel] Error 2
make[1]: Leaving directory '/opt/StartHere/cdk/linux-sh4-2.6.32.46_stm24_0209'
Makefile:2865: recipe for target '.deps/linux-kernel' failed
make: *** [.deps/linux-kernel] Error 2
root@ball:/opt/StartHere/cdk#
I do not go for it me.... 
Hi!
Ready my albis test builds, minimal error, missing files:
Create directory and null files micom.ko and frontends/multituner/*.ko, run.
(Tuner and frontend not needed albis iptv.?)
cdk /opt/Audioniek/StartHere/source /opt/StartHere/flash ufs913 || true
-- Result -------------------------------------------------------------
Output file(s) created in /opt/StartHere/flash/out:
53M
drwxr-xr-x 3 4,0K máj 16 14:34 kathrein
-rw-r--r-- 1 33 máj 16 14:34 Kathrein_UFS913_enigma2_flash_full.data.md5
-rw-r--r-- 1 53M máj 16 14:34 ufs913_enigma2_P217_CDK-rev951.zip
Output: Kathrein_UFS913_enigma2_flash_full.data > how to create uImage and rootfs?
make crosstool driver?
Rename *.dat to rootfs.img, flashing, but error:
Loading from nand0, offset 0x0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
** Unknown image type
Wrong Image Format for bootm command
ERROR: can't get kernel image!
STB8000> Loading from nand0, offset 0x0
Unknown command 'Loading' - try 'help'
STB8000> 1
Unknown command '1' - try 'help'
STB8000> 0x01
Unknown command '0x01' - try 'help'
STB8000> otm command
Unknown command 'otm' - try 'help'
STB8000>
.................................................................................
Reflashing FT232BM (DSS-20 dockstation):
usb 4-1: new full-speed USB device number 2 using uhci_hcd
usb 4-1: New USB device found, idVendor=0483, idProduct=3747
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-1: Manufacturer: ST
usb 4-1: SerialNumber: STMCLT1030
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver ftdi_sio
usbserial: USB Serial support registered for FTDI USB Serial Device
usb 4-1: Ignoring serial port reserved for JTAG
lsusb:
Bus 004 Device 002: ID 0483:3747 STMicroelectronics ST Micro Connect Lite
Bitbang mode work (if rebuild circuit)?:
http://openschemes.com/2011/10/25/bit-bang-jtag-programming-of-xilinx-cpld-using-ft232-homebrew-svf-player/6/
Hi!
My builds new repo Raxone STB8000_TDT_SH4, build Ubuntu 14.04 32 BIT.
Minimal error (ffmpeg /tmp, lirc.0.9.tar.gz download, attrib /boot dir 777) repaired and ready, but error:
run ufs913.sh:
adding: uImage.bin (deflated 0%)
adding: mtd_fw.sum.bin (deflated 98%)
adding: mtd_root.sum.bin (deflated 6%)
adding: ufs913.software.V1.00.B00.data (deflated 2%)
-----------------------------------------------------------------------
stat: stat ”/home/b/STB8000_TDT_SH4/flash/ufs913/tmp/FW/audio.elf” No files or directory
!!! WARNING: AUDIOELF SIZE IS ZERO OR MISSING !!!
IF YOUR ARE CREATING THE FW PART MAKE SURE THAT YOU USE CORRECT ELFS
-----------------------------------------------------------------------
stat: stat ”/home/b/STB8000_TDT_SH4/flash/ufs913/tmp/FW/video.elf” error: No files or directory
!!! WARNING: VIDEOELF SIZE IS ZERO OR MISSING !!!
IF YOUR ARE CREATING THE FW PART MAKE SURE THAT YOU USE CORRECT ELFS
-----------------------------------------------------------------------
Flashimage created:
03:02
-----------------------------------------------------------------------
To flash the created image copy the *.img file to
your usb drive in the subfolder /kathrein/ufs913/ ???
Remember, if this is the first time you flash Enigma2 or Neutrino,
you will need to flash the updatescript.sh first.
The script can be found in the extras folder, copy it to /kathrein/ufs913/ on your usb drive. ???
root@b:/home/b/STB8000_TDT_SH4/flash/ufs913#
All *.elf files in /root/boot directory
If copy *.elf files in /flash/ufs913/tmp/FW/ same error; no files???
How to flash Albis?
Rename files, flashing, not work:
nand_read_bbt: Bad block at 0x000007f40000
nand_read_bbt: Bad block at 0x000007f60000
nand_read_bbt: Bad block at 0x000007fc0000
nand_read_bbt: Bad block at 0x000007fe0000
** Unknown image type
Wrong Image Format for bootm command
ERROR: can't get kernel image!
STB8000>
If run make crosstool driver -j2, error:
INSTALL /home/turulbird/STB8000_TDT_SH4/driver/pti/pti.ko
INSTALL /home/turulbird/STB8000_TDT_SH4/driver/simu_button/simu_button.ko
INSTALL /home/turulbird/STB8000_TDT_SH4/driver/stgfb/stmfb/stm_v4l2.ko
INSTALL /home/turulbird/STB8000_TDT_SH4/driver/stgfb/stmfb/stmfb.ko
INSTALL /home/turulbird/STB8000_TDT_SH4/driver/stgfb/stmfb/stmcore-display-sti7105.ko
INSTALL /home/turulbird/STB8000_TDT_SH4/driver/stgfb/stmfb/stmvbi.ko
INSTALL /home/turulbird/STB8000_TDT_SH4/driver/stgfb/stmfb/stmvout.ko
DEPMOD 2.6.32.61_stm24_0217
depmod: WARNING: /home/turulbird/STB8000_TDT_SH4/tufsbox/cdkroot/lib/modules/2.6.32.61_stm24_0217/extra/compcache/ramzswap.ko needs unknown symbol lzo1x_decompress_safe
depmod: WARNING: /home/turulbird/STB8000_TDT_SH4/tufsbox/cdkroot/lib/modules/2.6.32.61_stm24_0217/extra/compcache/ramzswap.ko needs unknown symbol lzo1x_1_compress
make[2]: Leaving directory `/home/turulbird/STB8000_TDT_SH4/cdk/linux-sh4-2.6.32.61_stm24_0217'
make[1]: Leaving directory `/home/turulbird/STB8000_TDT_SH4/driver'
/home/turulbird/STB8000_TDT_SH4/tufsbox/host/bin/depmod -ae -b /home/turulbird/STB8000_TDT_SH4/tufsbox/cdkroot -F /home/turulbird/STB8000_TDT_SH4/cdk/linux-sh4-2.6.32.61_stm24_0217/System.map -r 2.6.32.61_stm24_0217
touch .deps/driver
???
O čemu vi ??
Hi!
My builds repo Raxone STB8000_TDT_SH4, build Ubuntu 14.04 32 BIT in VM, no error.
If run ufs913.sh:
adding: ufs913.software.V1.00.B00.data (deflated 2%)
-----------------------------------------------------------------------
stat: stat ”/home/turulbird/STB8000_TDT_SH4-master/flash/ufs913/tmp/FW/audio.elf” error: No files or directory
!!! WARNING: AUDIOELF SIZE IS ZERO OR MISSING !!!
IF YOUR ARE CREATING THE FW PART MAKE SURE THAT YOU USE CORRECT ELFS
-----------------------------------------------------------------------
stat: stat ”/home/turulbird/STB8000_TDT_SH4-master/flash/ufs913/tmp/FW/video.elf” error: No files or directory
!!! WARNING: VIDEOELF SIZE IS ZERO OR MISSING !!!
IF YOUR ARE CREATING THE FW PART MAKE SURE THAT YOU USE CORRECT ELFS
Flashimage created:
13:30
-----------------------------------------------------------------------
To flash the created image copy the *.img file to
your usb drive in the subfolder /kathrein/ufs913/
Remember, if this is the first time you flash Enigma2 or Neutrino,
you will need to flash the updatescript.sh first.
The script can be found in the extras folder, copy it to /kathrein/ufs913/ on your usb drive.
turulbird@VM:~/STB8000_TDT_SH4-master/flash/ufs913$
If copy *.elf files in /flash/ufs913/tmp/FW/ same error; no files???
How to flash Albis?
Please help Raxone.
@turulbird
This build or (https://github.com/Duckbox-Developers) is not builds for final firmware.
This builds if for easy build and modified driver,kernel or python plugin for enigma and put/change in basic HDMU or another firmware for ufs913 etc.
My version of builds is modified kernel and drivers for albis8000 and need HDMU firmware for ufs913.
In ufs913 HDMU firmware change drivers and kernel to work on albis8000.
To fix problem audio.elf and video.elf just put audio.elf and video.elf in dir STB8000_TDT_SH4/tufsbox/release/lib/firmware and rerun
STB8000_TDT_SH4/flash/ufs913/ufs913.sh (fakeroot ./ufs913.sh)
Thanks, run, but kernel panic (after nand erase):
VFS: Mounted root (jffs2 filesystem) on device 31:1.
Freeing unused kernel memory: 116k freed
Warning: unable to open an initial console.
Failed to execute /bin/devinit. Attempting defaults...
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
@Raxone
This error can be improved or start over?
But it has finally started...
u-boot: stb8000
Rebuild image other system, same error...
pozdrav drustvo. da ozivim malo ovu temu. posto je tema slicna mom problemu. naime vidio sam da ovdje ima velikih znalaca. imam mag 250 koji nedaje znakove zivota. procesor mu je isto sti 7105. trebao bih napravit mu jtag i vratit ga u zivot. kako napravit konekciju i ubacit mu software. hvala unaprijed
nema nikog ovdje vise? ili?
Ako nemaš U-Boot preko UART-a, odnosno znaš da je obrisan, treba ti FT2232H/FT4232H Mini Module (isključivo ti su službeno supportani) da bi mogao preko JTAG-a poslati U-Boot kojeg ćeš koristiti da zapišeš sve na flash.
Googlao sam slike ploče, čini mi se da s jedne strane ima standardni 20-pinski JTAG konektor kao i većina STi7105 ploča.
Detaljnije ti ne mogu pomoći ovako na brzinu. Trebalo bi češljati one ruske forume pa na njima naći informacije.
pokusavam napravit kabal uart da ga mogu spojit. dali moze od samsunga kabal? i trbaju mi driveri, jer ga prepoznaje kao usb kabal
Radi jtag na mag250-u.
pokusavam napravit kabal uart da ga mogu spojit. dali moze od samsunga kabal? i trbaju mi driveri, jer ga prepoznaje kao usb kabal
Kupi FT2232H ili FT4232H. S njim možeš raditi i UART i JTAG.
Ne znam s kojim Samsung kabelom radiš, ali trebaš USB-UART adapter koji ti se pojavi kao COM port na Windowsima ili ttyUSBx na Linuxu.
pozdrav. evo ja dobio programator nakon mjesec dana, i krenuo.znaci sve je super krenulo, ali ovdje stane. mozda grijesim putanju fajla. dali zna netkohttp://www.upslike.net/images/2017/02/16/327a12a3fcda8409a9dbf9521b62102f.png
Pokreni to kao admin? Win10 ti ne dozvoljava drljanje po C: disku (rootu diska) bez admin ovlasti.
probao sam. opet isto ja sam original boot preimenovao u u-boot.o i stavio na c disk. neznam gdje je problem. radim po upustvima sa neke ruske stranice, i sve je bilo super do ovoga
Ajde napravi folder "boot" na C:\ disku i kopiraj fajl unutra pa zadaj tu putanju.
